INSTALLING LEWP ON IBM NETWORKS


LEWP supports the IBM PC Network and the IBM Token-Ring Network.  
Before you begin on-line installation procedures, please review your 
CUSTOMER SUPPORT GUIDE.

These instructions assume your network is set up and ready to operate.  
To install LEWP on an IBM network, you will:

    1.   Copy LEWP program files to the server by running the INSTALNT 
         program.
         
    2.   Copy the printer driver files to the server by running the 
         PRINSTAL program.
         
    3.   Copy the Spelling and Help files to the server.
         
          



                COPYING LEWP PROGRAM FILES TO THE SERVER


To install LEWP on a network server, you run the INSTALNT program on 
the LEWP Master Disk.  It copies the LEWP program files onto the 
server.  Installation creates a subdirectory (\LEWP) where LEWP files 
are stored.

Before you begin, note that the commands in this section include the 
variables X, Y, and Z.  Substitute the following information for these 
variables:

    X = the letter of the logical drive.
    
    Y = the name of the server.
    
    Z = the network name for the shared directory on the server.
    




To run INSTALNT:

    1.   Make sure the server is booted.
         
    2.   Type NET USE X: \\Y\Z and press RETURN, substituting the 
         correct information for the variables.
         
         In the example NET USE F: \\SMITH\ROOT, F is the letter of the 
         logical drive, SMITH is the name of the server, and ROOT is 
         the network name for the shared directory on the server SMITH.
         
    3.   Type X: and press RETURN, substituting the letter of the 
         logical drive for X.  This will make the logical drive the 
         current drive.
         
    4.   Insert the LEWP Master Disk in Drive A.
         
         
         
         


    5.   Type A:INSTALNT X and press RETURN, substituting the letter of 
         the logical drive for X.  This command creates a subdirectory 
         (\LEWP) on the server.  The program files from the LEWP Master 
         Disk are copied into this subdirectory.
         
    6.   When the X prompt reappears on the screen, you have completed 
         this procedure.  Remove the LEWP Master Disk from Drive A.
         Next you will copy printer drivers to the server.
    
    
    
    
    
    
    
    
    
    
    
    


                  COPYING PRINTER DRIVERS TO THE SERVER


To prepare LEWP to recognize the printers you use on your network, you  
run the PRINSTAL program on the LEWP Tutorial & Utilities Disk.  This 
copies the printer driver files, the software instructions that run a 
particular printer, to the server.

Before you begin, note that the commands in this section include the 
variables X, Y, and Z.  Substitute the following information for these 
variables:

    X = the letter of the logical drive.
    
    Y = the name of the server.
    
    Z = the network name for the shared directory on the server.
    




To run PRINSTAL:

    1.   Make sure the network server is booted.
         
    2.   Type X: and press RETURN, substituting the letter of the 
         logical drive for X.  This makes the logical drive the current 
         drive.
         
    3.   Insert the LEWP Tutorial & Utilities Disk in Drive A.
         
    4.   Type A:PRINSTAL XT and press RETURN.
         
         A printer selection menu appears.  You can choose up to five 
         printers. For each one you select, a printer driver file is 
         copied to the \LEWP\BINS subdirectory on the network server.
         
         
         
         
         


    5.   Select your printer(s).  Press the UP ARROW or DOWN ARROW keys 
         to move the screen arrow next to the name of your printer.
         
         Press PAGE UP or PAGE DOWN if you need to see more printers on the 
         list.
         
         If your printer is not listed, you can print with a 
         preinstalled driver called PRINTER.  (Refer to PREPARING YOUR 
         PRINTER in the CUSTOMER SUPPORT GUIDE.)

    6.   Press RETURN.  The printer's name is highlighted.  Choose up 
         to four more printer models by repeating Steps 5 and 6.
         
    7.   Press END when you finish.  The screen displays your 
         selection(s).
         
         
         
         
         


    8.   Press RETURN if the selections are correct.
         
         OR
         
         Press ESCAPE to start over.
         
    9.   When a screen message says you've completed the procedure, 
         remove the disk from Drive A.
         
         
         
         
         
         
         
         
         
         
         
         


                     COPYING SPELLING AND HELP FILES


Now copy the Spelling and Help files to the \LEWP\BINS subdirectory on 
the server.  You need the LEWP Spelling and Help Disk.

Before you begin, note that the commands in this section include the 
variables X, Y, and Z.  Substitute the following information for these 
variables:

    X = the letter of the logical drive.
    
    Y = the name of the server.
    
    Z = the network name for the shared directory on the server.







To copy the Spelling and Help files:

    1.   Make sure the server is booted.
         
    2.   Type X: and press RETURN, substituting the letter of the 
         logical drive for X.  This will make the logical drive the 
         current drive.
         
    3.   Insert the LEWP Spelling and Help Disk in Drive A.
         
    4.   Type A:SPLHLPXT and press RETURN.
    
    5.   Make sure the LEWP Spelling and Help Disk is in Drive A.
         
         
         
         
         
         
         


    6.   Press any key to continue.
         
    7.   When a screen message says you've completed the procedure, 
         remove the disk from Drive A.
         
    
    LEWP is now completely installed on the network server.  Proceed to 
    MAKING NETWORK BOOT DISKS in the CUSTOMER SUPPORT GUIDE.











ompleted the procedure, 
         remove the disk from Drive A.
         
    
    LEWP is now completely installed on the network server.  Proceed to 
    MAKING NETWORK BOOT DISKS in the CUSTOMER SUPPORT GUIDE.